返回列表 发新帖

4G Cat.1 for NEO/NEO Core/NEO Air User Manual

[复制链接]

365

主题

1406

帖子

6317

积分

管理员

Rank: 9Rank: 9Rank: 9

积分
6317
发表于 2023-9-4 10:03:01 | 显示全部楼层 | 阅读模式
Keywords: 4G Cat.1  NEO  Air  NEO Core Internet  Ubuntu  Debian  Linux
Description:
The NanoPi NEO Core(abbreviated as "NEO Core") is an alternative NanoPi NEO that works like a CPU board with male pin-headers. It has the same form factor as the NanoPi NEO and same pin descriptions. The connectors and ports are populated to pin-headers on the NEO Core. The NanoPi NEO Core has ESD protection for its MicroUSB port and TF card slot. In addition the NEO Core can have an optional onboard eMMC flash which is preferred by industrial customers.




The NanoPi NEO(abbreviated as NEO) is another fun board developed by FriendlyARM for makers, hobbyists and fans.


The NanoPi NEO Air is a 40 x 40mm open source ARM board for makers.It uses an Allwinner H3 Quad Core A7 processor at 1.2GHz. Its pins are compatible with the NanoPi NEO(V 1.2) and its 24-pin header is compatible with Raspberry Pi's GPIO pin headers.
The NanoPi NEO AIR features 512MB of 16bit wide DDR3 RAM, 8GB eMMC and one MicroSD slot. It has WiFi & Bluetooth and DVP camera interface(YUV422). The DVP camera interface can support friendlyarm's 5M-pixel camera module
It has enhanced power circuit design and better heat dissipation.



They all based on Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz


Now we designed 4G Cat.1 for all these H3 based NEO serial boards.
NEO_Cat1.jpg







回复

使用道具 举报

365

主题

1406

帖子

6317

积分

管理员

Rank: 9Rank: 9Rank: 9

积分
6317
发表于 2023-9-4 13:22:01 | 显示全部楼层
Usage with Debian:

回复 支持 反对

使用道具 举报

54

主题

216

帖子

1万

积分

允许发帖

积分
10790
发表于 2023-9-6 10:31:34 | 显示全部楼层
本帖最后由 Mcuzone_WXJ 于 2023-9-6 10:42 编辑

4G Cat1 works with NEO/NEO Core+Debian:


Hardware platform:
NanoPi NEO/ NEO Core   4G Cat.1

Software Platform:
friendlycore-xenial

Image file:
h3_sd_friendlycore-xenial_4.14_armhf_20210618.img

NanoPi NEO/ NEO connects to a PC through a serial port.
Open the serial port tool and enter ifconfig. You can see that 4G is identified as eth1 but has no IP address. In root mode, enter "udhcpc -i eth1" to obtain the IP address.
The identification results of NEO and NEO Core are the same.

600E.png




回复 支持 反对

使用道具 举报

54

主题

216

帖子

1万

积分

允许发帖

积分
10790
发表于 2023-9-6 10:37:08 | 显示全部楼层
本帖最后由 Mcuzone_WXJ 于 2023-9-6 11:00 编辑

4G Cat1 works with NEO Air+Debian:

Hardware platform:
NanoPi NEO Air   4G Cat.1

Software Platform:
friendlycore-xenial

Image file:
h3_sd_friendlycore-xenial_4.14_armhf_20210618.img

NanoPi NEO/ NEO connects to a PC through a serial port.
Open the serial port tool and enter ifconfig. You can see that 4G is identified as eth1 but has no IP address. In root mode, enter "udhcpc -i eth0" to obtain the IP address.

Air600EA_Air.png

回复 支持 反对

使用道具 举报

54

主题

216

帖子

1万

积分

允许发帖

积分
10790
发表于 2023-9-6 10:58:42 | 显示全部楼层
4G Cat1 works with NEO/NEO Core/NEO Air+Ubuntu:

Hardware platform:
NanoPi NEO/ NEO Core   4G Cat.1

Software Platform:
friendlycore-focal

Image file:
h3_sd_friendlycore-focal_4.14_armhf_20210618.img

NanoPi NEO/ NEO connects to a PC through a serial port.
Open the serial tool,use the nano in the/etc/resolv.conf file add "nameserver 8.8.8.8"
dns(1).png


Enter ifconfig and you can see that 4G is recognized as enx..
ifconfig.png


The identification results of NEO/NEO Core/NEO Air are the same.

回复 支持 反对

使用道具 举报

发表回复

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

快速回复 返回顶部 返回列表